Mantor's Skin2Skin Retainer: A Comprehensive Guide

Skin2Skin Retainer by Mantor Restorer

 

This innovative 2-in-1 retainer offers two distinct methods to retain the foreskin, each designed to enhance your restoration journey.

 

The first method – Skin to skin retaining – providing a direct contact between the glans and the inner foreskin, promoting sensitivity and encouraging natural skin development. This approach is widely recognized as the most effective way to restore sensitivity and promote skin dekeratinization. 

 

“Faux-Skin” Retainer: Perfect for beginners, this choice offers a supple, elastic texture that imitates foreskin. It offers comfort for wearing throughout the day and night, ensuring the glans stays covered. During nocturnal erections, it snugly adheres to the skin and provides gentle tension. The “faux-skin” design features a spacious center aperture, facilitating effortless urination without mess. Its snug fit guarantees it remains secure during everyday tasks.

 

In this page we will guide you step by step how to use and get the most out of our unique retainer:

 

Skin to Skin retainer mode

Step 1: Verify the correct positioning of the Skin2Skin Retainer. The thick ridge, located approximately two-thirds up from the base, should be oriented outward, while the thinner ridge at the center should face inward. It’s essential for optimal grip.

Mantor skin to skin

Step 2: Pull the skin forward to cover the glans, then position the wide opening of the retainer on top. Using your index finger and thumb, support the glans from behind (white arrows), and gently push the retainer towards the body to guide the glans through the center hole (green arrow) until it’s fully out.

Step 3:

Depending on your skin’s length, you can adjust the position of the retainer:

Down towards the glans to have the minimal amount of skin under the gripper. (Pic .1)

Up towards the base of the penis shaft to increase the length of skin for gripping. (Pic .3)

Over time, you’ll identify the best area to grip, or you can alternate between the two at your choice. 

 

Tip#1: To move the retainer on the shaft, insert a finger under the gripper and pull gently. (Pic .2)

Tip#2: If necessary, trim your pubic hair to prevent it from getting caught under the retainer.

 

Step 4: Take the G-pin and place it on the glans. (Pic .1) While keeping the G-pin on the glans, hold the retainer and slowly move it towards the glans. Be careful to not apply too much pressure on the G-pin or move the retainer too quickly. This step may require some practice, so you may need to repeat it a few times at the beginning. The skin should reach up to the end of the gripping neck for the optimal grip. 

 

Tip #1: Bring a portion of the skin to the G-pin’s edge to utilize it as an anchor for pulling more skin into the gripping area afterward. (Pic .2)

 

Tip #2: If you don’t have much skin, it’ll be easier to do it while seated.

Step 5: Aligning the grip.

 

If you need to pull more skin onto the gripping zone, start by holding the skin you can grab (hence the anchored point from the previous stage), and with the fingers pull it gently. (Pic .1)

 

If you have gripped an excessive amount of skin, you can withdraw it by pulling on the G pin cover. (Pic .2)

 

Tip: You can create gentle tension by pulling enough skin. The G-pin and the retainer will keep it in position.

 

Step 6: Once you are happy with the grip, flip the base of the gripper forward to bring it to its final position.

 

 

More cool things you can do:

You can manually stretch your skin

to give some short bursts of tension:

 

-By holding the retainer and pulling. (Pic .1)

 

-By turning it around in place.(Pic .2)

 

-By Turning and pulling at the same time.(Pic .3)

 

Faux-skin Retainer mode

Step 1: Verify the correct positioning of the Skin2Skin Retainer. The thick ridge, located approximately two-thirds up from the base, should be oriented outward, while the thinner ridge at the center should face inward. It’s essential for optimal grip.

Mantor skin to skin

Step 2: Bring the skin until it reaches the thick ridge. (Pic .2, black arrow)

If you don’t have much skin, gently press on the glans to create a skin surface you can hold. (Pic .1, white arrow)

Keep the skin in place by forming a ring around it using your fingers. (Pic .2)

Step 3: Flip the wider end of the retainer down towards the glans. Place all five fingers inside the cone and spread them wide simultaneously. 

Step 4:

Ensure there’s enough skin under the gripper all around to secure a good grip. (Pic .1)

You can aim your urethra to be in the center of the opening to ensure a clean and mess free visit to the bathroom. (Pic .2)

 

You can use it as a Night Retainer*, to protect the glans and benefit from the nocturnal erections for some tugging during sleep. 

 

*Please ensure that you can manually cover your glans with your skin when erect before attempting night retention for the first time…

Join our growing community